Aircraft Light Circuit
aircraft Light Hookups diagram
Aircraft Lighting Circuit directions
Aircraft Light Circuit Dimensions
bulb led sizes for aircraft light
chip LED sizes
chip LED sizes
light dimensions
chip light dimensions
5mm LED
3mm LED
1.8mm LED

RC Aircraft LED Lights & Lighting Circuit Systems

Light Group
9 Volt Battery Strap/Switch
Regular price $15.00
  • In stock, ready to ship
  • Inventory on the way


Use our Aircraft Light Circuit to easily add realistic LED lighting to your Model Plane or Jet, even your Helicopter Model or RC Aircraft and Airliners.

This circuit is small, easy to conceal, and pretty simple to use.  This circuit will give you all the lighting special effects your plane needs including strobes, beacon, navigation, landing, and even interior lighting.  This circuit can power up to 8 LEDs.

Aircraft Light Circuit-only includes:

  • 4 Wired Male Connectors that mate to the board's positions
  • 1 Wired Female connector for power input 7-12 Volts
  • 6 inches of shrink tube for connections

Aircraft Light Circuit plus lights includes:

  • Your Choice of Size of LEDs:
  • A Warm White Cabin Light
  • 3 x Cool White LEDs for use on the 3 Strobe Hookups
  • 1 Red and 1 Green LED for use on the Wingtips Hookups
  • 1 Red LED for the tail Beacon Hookup
  • Wired Pin Connectors
  • 6 inches of shrink tube for your connections

Visit our LED Size Guide for exact LED dimensions. All LEDs will exhibit the flashing behavior described above when connected to the circuit board. Choose the LED size that will best suit your airplane's scale.

Wire Length - Each light can be up to 16 inches from the circuit board.  (You get 8 inches of hookup wire to the board, plus each light is pre-wired with 8 inches) For a large plane choose the 3mm-Long Wire option which allows each light to be up to 28 inches from the Circuit Board (14-inch hookups + 14 inch pre-wired LEDs)

Landing Lights and Interior lights - These lights are optional and not included in the kit.  If you want these orders any of our 5-12 Volt Lights separately.  The web pages containing these lights are called out in the Circuit Only option below.


Select Circuit Only and use it with any of our Solid LEDs.  There are many configurations that you can get for your model.  For example, you can put together your own group of lights with multiple light sizes, or double up on the lights on some locations like the landing lights.  You could even add a bright Mega LED of any color to keep your RC craft in sight in the dark or in a busy flying environment.

Choose from any of our pre-wired for 5-12 Volt use such as:


  Typical power supplies you could use:

  • RC LiPo batteries with 2 or 3 cells
  • a 9-volt battery
  • or our 12-volt power supply

Circuit Light Hookups: refer to the diagram on the Plane Sketch and Circuit Board Image

      (all LED hookups to the board are done using our male pin connectors)  4 male pin connectors are included with all board purchases. A wired female pin connector is included for power hookup.

  • Double Flash (2X Position)- LED(s) wired to this position cycle through 2 flashes and then a pause.  (like Airbus/Cessna wind strobe) Flash rate is adjustable*
  • Single Flash (1X Position)- LED(s) wired to this position flash On and then Off (Pause).  The LED is Off about twice as long as it is On. The flash occurs at a similar time as the Double Flash (like the Boeing wing and tail strobe ) The flash rate is adjustable *
  • Single Flash (FL Position)  This position is configured for a Red Beacon Tail Light.  It has the same Flash Rate as the Single Flash and Flashes just prior to the Single Flash
  • Steady Light (5V! Position) Use for steady lights on your plane, like Landing lights and interior lighting

    * Adjustable Flash timing is done by a small set screw on board.  You have adjustable rates between Flashing about 2 times a second and every other second. 

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Recently viewed